• Fits 1939-1948 Ford PowerGEN alternator
• Made out of show quality raw aluminum
• Made in the USA
• Set screw type mount

The post OTB Gear Unpolished Finned 1939-1948 Ford Style PowerGEN Alternator Cover appeared first on GoodSpeed USA.

• Fits 1939-1948 Ford PowerGEN alternator
• Made out of show quality polished aluminum
• Made in the USA
• Set screw type mount

The post OTB Gear Polished Finned 1939-1948 Ford Style PowerGEN Alternator Cover appeared first on GoodSpeed USA.

• Show quality unpolished aluminum
• Fits 1-1/4″ opening with included grommet
• Breather stem measures 3/4″
• 2-3/4″ casting diameter
• Made in the USA

The post Unpolished Finned Aluminum Round Push In Valve Cover Breather For 1-1/4″ Hole appeared first on GoodSpeed USA.

• Made out of show quality aluminum in a satin finish
• Made in the USA

– Can be plumbed thru the bottom or backside surfaces, which reduces your oil line clutter
– Use a commonly available spin on type oil filter (included)
– Uses 3/8″ NPT fittings (not included)
– Drilled and tapped for 3/8″ mounting hardware (not included)
– Two plugs are provided to cap off the unused fitting holes
– Dimensions: 5-1/2″ H, 3-3/4″ W, 5-1/8″ projection

The post OTB Gear Satin Cast Finned Remote Oil Filter Cover Assembly For Hot Rod appeared first on GoodSpeed USA.

• Made out of show quality polished aluminum
• Made in the USA

– Can be plumbed thru the bottom or backside surfaces, which reduces your oil line clutter
– Use a commonly available spin on type oil filter (included)
– Uses 3/8″ NPT fittings (not included)
– Drilled and tapped for 3/8″ mounting hardware (not included)
– Two plugs are provided to cap off the unused fitting holes
– Dimensions: 5-1/2″ H, 3-3/4″ W, 5-1/8″ projection

The post OTB Gear Polished Cast Finned Remote Oil Filter Cover Assembly For Hot Rod appeared first on GoodSpeed USA.

• Universal (will fit most GM cars & trucks)
• Front ports are tapped for 5/16″x8″ brake line
• Rear ports are tapped for 9/16″x8″ brake line
• 1″ bore
• Made out of show quality polished aluminum
• Plunger for power and manual brakes
• Mounting holes measure 3-1/4″ apart
• Measures about 8″ in length and 3-3/4″ wide
• Includes 2 plugs to block unused ports

The post Universal GM Style Polished Aluminum Master Cylinder 1″ Bore appeared first on GoodSpeed USA.

The post Pair OTB Gear Primed Guide 682-J Headlight Bucket Housings w/ Badge appeared first on GoodSpeed USA.

• Signal has a two filament amber bulb with a clear lens
• Housings only (ready to use with your 7″ headlight bulbs)
• Gloss black guide housing with a smooth finish that can be painted
• The parking/turn signal shell is a sleek die casting/n rather than a sheet metal stamping, this is secured to the headlight by two screws from the underside providing a much cleaner appearance when compared to the original
• The glass parking light lens is a duplicate of the original 682-C Series 2 design/n better than ever thanks to modern computer designed stainless steel molds
• The mounting flange installs inside or outside of the headlight housing/n secured by 4 stainless button head screws. Mount it outside for the old school look, or inside for a cleaner appearance. The original flange was riveted to the outside of the housing, like it or not
• Wire thru the hollow mounting bolt, or the underside conduit hole/n your choice. The original had a solid mounting bolt.
• We provide you with an extra 2 filament turn signal bulb for backup

The post Pair Guide 682-C Style Headlight Buckets w/ Chromed Amber Turn Signal appeared first on GoodSpeed USA.

The post Cast Stainless Steel Steering Arm For 1928-1948 Ford Spindles appeared first on GoodSpeed USA.

Pair Polished Finned Aluminum Drum Brake Scoops

• Designed for 1939-1948 Ford backing plates (can be used on other applications)
• Provides cool air to your brakes while adding a cool look to your car
• Made out of polished aluminum
• Installation requires drilling and tapping into your back plates
• Measures 4-1/2″ high X 3-1/2″ wide X 2″ deep
• Drilled and tapped for 1/4-20 screws (not included)
• Includes drilling template
• Made in the USA
• Sold as a pair

The post Pair Polished Finned Aluminum Drum Brake Scoops For 1939-1948 Ford appeared first on GoodSpeed USA.

The post OTB Gear Cast Aluminum Finned Firewall Wire Port For Hot Rods appeared first on GoodSpeed USA.

Finned Polished Firewall Port

• OTB Polished Firewall Port
• Cast aluminum is then polished to a show finish.
• Conceals a backplate and bushing that allows up to 3/4″ diameter of wiring to pass through the firewall
• 2 7/8″ diameter and 1 7/8″ deep
• Made in the USA

The post OTB Gear Polished Finned Firewall Wire Port For Hot Rods appeared first on GoodSpeed USA.

Adjustable Length Headlight Conduit

• Made with 4 wires so you can power parking lights and turn signals.
• It can be cut to the desired length as end fittings are made of 3 pieces and contain an “O” ring-like hydraulic fitting.
• Cut to length and screw back together.
• Fittings are chrome-plated brass for a long, shiny life.
• Measures 13-1/2″ long in total length
• Sold as a pair

The post Pair OTB Gear 4 Wire Black Adjustable Length Headlight Conduit appeared first on GoodSpeed USA.

The post Pair OTB Gear 4 Wire Stainless Steel Adjustable Length Headlight Conduit appeared first on GoodSpeed USA.

The post Unpolished Cast Aluminum Finned Bolt-On Hood Air Scoop – OTB Gear appeared first on GoodSpeed USA.

• Great for hot rods, & muscle cars
• Measures 14-3/4″ L x 11″ W x 3-3/8″ H & the opening is 2-3/4″ H
• Secure to your hood with 1/4″-20 hardware (not included)
• Made in the USA out of A-356 alloy (aluminum)
• Highly polished (show car quality)
• Includes a full-scale drilling template to tape to your hood

The post Polished Cast Aluminum Finned Bolt-On Hood Air Scoop – OTB Gear appeared first on GoodSpeed USA.

The post Pair Black Guide 682-C Style Headlight Buckets with Amber Turn Signal appeared first on GoodSpeed USA.

Triple Remote Brake Fluid Reservoir

• Designed for hot rods and custom applications (firewall mount)
• It helps maintain proper fluid level in the master cylinder
• Lines can be run out of the bottom of the backside of the reservoir
• Drilled and tapped for 1/8″ NPT fittings
• Requires (4) 1/4″-20 threaded studs for mounting (not included)
• Measures 6″ L x 2″ W x 3.5″ H
• Sprocket-style caps look like intermeshed gears
• Made out of heavy-duty aircraft-grade aluminum with a satin finish
• Car show quality
• Made in the USA

The post Triple Remote Brake Fluid Reservoir – Custom Hot Rod – Satin Finish appeared first on GoodSpeed USA.

Triple Remote Brake Fluid Reservoir

• Designed for hot rods and custom applications (firewall mount)
• It helps maintain proper fluid level in the master cylinder
• Lines can be run out of the bottom of the backside of the reservoir
• Drilled and tapped for 1/8″ NPT fittings
• Requires (4) 1/4″-20 threaded studs for mounting (not included)
• Measures 6″ L x 2″ W x 3.5″ H
• Sprocket-style caps look like intermeshed gears
• Made out of heavy-duty polished aircraft-grade aluminum
• Car show quality
• Made in the USA

The post Triple Remote Brake Fluid Reservoir – Custom Hot Rod – Polished Show Quality appeared first on GoodSpeed USA.

The post Dual Remote Brake Fluid Reservoir – Custom Hot Rod – Satin Show Quality appeared first on GoodSpeed USA.